Accessories for N-EVAP Evaporators

 

  1. Adapter, Pasteur-Pipet, NA0636 (dozen)
  2. Fitting, Pasteur Pipet, P0635, (each), Option: -P
  3. Same, acid-resistant, P0635-R (each) Option: -RP
  4. Luer-Lok needle, SS, 4-inch, NA0603 (dozen)
  5. Luer-Lok needle, SS, 6-inch, NA0605 (dozen)
  6. Luer-Lok needle, Teflon-coated, NA0603-T (dozen)

 

Water Bath Floats

Hollow polypropylene spheres are placed in N-EVAP water baths to reduce water evaporation rate and allow temperature to reach 100° C.
Floats for 8.5 inch diameter bath Catalog No. NA0627
Floats for 12 inch diameter bath Catalog No. NA0714
Floats for 18 inch diameter bath Catalog No. NA1504
Pasteur Pipet Adapters

Plastic adapters that hold disposable 5 3/4 inch long glass pipets and attach to luer fittings. Internal flow control orifice insures even gas flow. They are available by the dozen or in sets of 50 or 100.
Adapters 1 dozen Catalog No. NA0636
Adapters 50 each Catalog No. NA1325
Adapters 100 each Catalog No. NA1425

 

Needles

Standard needles for N-EVAP and MULTIVAP are 4 inches long 19-gauge stainless steel. They are available by the dozen or in sets of 50 or 100.
4 inch 19ga 1 dozen Catalog No. NA0603
4 inch 19ga 50 each Catalog No. NA1303
4 inch 19 ga 100 each Catalog No. NA1403
Longer 6 inch 19 gauge needles. Used with deep test tubes.
6 inch 19 ga 1 dozen Catalog No. NA0605
6 inch 19ga 50 each Catalog No. NA1305
6 inch 19 ga 100 each Catalog No. NA1405
Larger diameter needles. Used for greater Nitrogen flow and faster evaporation.
4 inch 16ga 1 dozen Catalog No. NA1105-16
4 inch 14 ga 1 dozen Catalog No. NA1105-14
6 inch 16ga 1 dozen Catalog No. NA1106-16
6 inch 14 ga 1 dozen Catalog No. NA1106-14
All sizes can be Teflon coated for acid resistance and easier cleaning. Add a -T to the catalog numbers above.
Air Compressor

Bench top unit supplies clean air at 13 lpm and 8 psig. Quiet, maintenance free includes filterand tube fitting.

Compressor 120 volt .......Catalog No. NA0401
Compressor 240 volt ....Catalog No. NA0401-2
Pressure reducing regulator for gas supply

The gas pressure for N-EVAP and MULTIVAP instruments must be between 5 and 20 psig. If the supply is greater than 20 psig, tubing may blow off the connectors. This regulator reduces inlet pressure from up to 300 psig to a variable output O to 30 psig. The output pressure is indicatedon a gauge. Connectors are 1/4 inch MNPT on the inlet and 1/4 inch compression tube fitting on the outlet. Other fittings are available. Please specify your requirements.

Catalog No. NA0630
Sample holders for large or small vessels

These two special sample holders are designed to replace the standard sample holder on the model 111 N-EVAP. The 6 position part holds large test tubes or beakers 30 mm to 48 mm diameter. The 12 position part holds micro vials 5 mm to 12 mm diameter.

6 position for large tubes
Catalog No. .......................................NA1113
12 position for micro vials
(not shown) Catalog No.................... NA1132